How To Fix A Toilet Handle That Has To Be Held Down

You have to manually hold the flapper open by holding down the toilet lever because the flapper is unable to stay afloat by itself. I took a look inside and I am wondering if it has something to do with the chain or the flapper.

How To Stop Holding The Toilet Handle Down So It Flushes Completely Hometalk

Remove the lid from tank and make sure the chain has only 14 inch of slack.

How to fix a toilet handle that has to be held down. Check the slack in the chain when you operate the toilet handle. With the flush arm down and the flapper down pull the chain straight up with no slack and align the chain with the nearest hole in the flush arm. Make note of the hole and the link that is right below that hole.

This problem is caused by too much slack in the lifting chain that connects the flush lever to the flapper. The shut-off valve is usually located on the base of your toilet near the back. Unscrew the bolt from the new handle using your screwdriver and then push the handle through the hole in the toilet.

A nut holds the toilet handle in place. I have gotten calls regarding this problem and if the plastic handle doesnt break first from the pressure you have to exert to get the toilet handle to go down then replacing that seal will do it for you. When you hit the trip lever the arm should only move 14 inch before activation Adjust the water level.

Turn off the water shut-off valve for your toilet and press the lever to empty the tank. As the water level is lowered flapper is lowered at the same time ultimately closing the inlet so that the water can be refilled. When you release the handle the flapper should settle down into the flush valve with just a small amount of slack in the chain.

In this video I show how to easily fix a A toilet where you have to hold down the handle for the whole flush. When the handle is depressed the flapper should lift into a nearly vertical position so you can see the bottom of the flapper. Your bolt should screw on manually at first and then more tightly onto the base of the handle using the wrench.

I have to hold the handle down to flush my toilet completely. If not loosen the nut until the handle operates smoothly. Try the handle and if it works leave the lock nut in this position.

I have to hold the handle down for a long time. Lift tank top find chain see if you can shorten it or take up slack. Loosen the nut from inside of the tank using an adjustable wrench if necessary.

These can be bought at home centers. This means you will turn the nut clockwise to loosen. Just as you would with a non-dual flush toilet loosen the lock nut which sits directly behind the handle on the inside of the toilet tank by turning it clockwise since it has reverse threads.

Mary on Jan 23 2018. Unless you turn water off below toilet water will run while you make the fix. TOILET HANDLE HOLD DOWN - EASY FIX.

This extra length means that the flapper doesnt lift high enough so theres a lot less volume of water flowing into the toilet bowl. But yes that should cure the problem. Once you have decided to discard the old handle you will need to replace the part.

Chain located in tank attached to flushing lever is caught under flap in tank. When the tank is empty the flapper falls back down into the valve seat sealing the opening and allowing water to refill the tank. On most toilets this nut is left-handed or reverse-threaded which is opposite from a typical nut.

If the toilet doesnt flush completely unless you hold the handle down for the entire flush cycle its usually because the flapper is not fully lifting away from the flush valve. It isnt a flapper per se but rather a ring. When the handle is depressed a chain or lift wire connected to the handle rod lifts the flapper away from the valve seat and allows the water to flush down out of the tank and into the toilet bowl.

Unhook the chain from the flush arm and place the arm in the down position like you were pushing the toilet handle down. Holding Toilet Handle Down If you have to hold the toilet handle down to get all the water into the bowl this means the chain is too long. Look inside the tank to find the metal nut directly adjacent to the handle.

Removing all the water in the tank will allow you to tighten the handle from the inside properly. I am noticing that the flapper does not stay up unless the handle is being held down.

Need To Hold Down Handle To Get Powerful Flush Youtube