How To Remove Plastic Screws From Toilet Seat

Light the plastic nut on fire. Push the anchor bolts of the new seat through the holes and hand tighten the nuts.

Help How Do I Replace This Toilet Seat Diynot Forums

You can use bleach baking soda or vinegar.

How to remove plastic screws from toilet seat. Put on goggles to protect your eyes. Simply pry open the cover behind the seat to expose the bolts head. Eventually you should be able to lift the screws right out of there.

But the 3rd toilet had bolts that would not budge. Report this comment Thanks for reporting. In an attempt to destroy the plastic screws for removal I bored a hole through the center of them with a drill and still couldnt crack them to remove them.

This vid shows how to remove a stripped expansion bolt with rubber gasket from the base of a Toto toilet. Hold the bolts in place with the screwdriver as you turn the plastic nuts on the underside of the back of the toilets bowl. Simply put the plastic toilet seat screws were so stuck that I stripped them completely with my screwdriver.

Plastic bolts wont turn. When its time to replace your toilet seat you can usually use a screwdriver and pliers to remove the. Unscrew bolt replace seat re-screw bolt.

To remove the toilet seat start by locating where the seat is joined with the toilet. Im trying to replace an old toilet seat but unfortunately the plastic screws holding the seat to the toilet are old and on tight and it didnt take much to completely strip the hole on one of the plastic screws. The first two took about 2 minutes each.

Removing a stripped plastic toilet seat screw. Remove the seat bolts and lift off the seat. When it comes to removing toilet seats the big gun is a drill with a 14-inch drill bit.

Many toilet seats are held in place by plastic screws and nuts which wear out over time. Many new toilet seats are attached to the toilet bowl with two plastic bolts and nuts. Then insert the bit into the bottom of a stuck metal nut that you cant turn at the point at which it meets the bolt.

Unscrew the bolt with a pliers or a screwdriver while you hold the nut underneath with the pliers. With some diagonal wire cutters you could nibble away at the plastic. Place the toilet seat in the right position and start tightening the bolts.

Answer 2. This pushes the coned nut down and releases the expansion pressure. Use a wrench screwdriver or locking pliers to unscrew the seat off.

To removethe screw locates Into the nutone turn. Shower pipe broke off I need to remove old pipe out to put the new. First take a look at the bolts that secure the seat.

If the bolts or nuts are plastic they cant corrode and will come off easily. Step 3 Spray penetrating lubricant in the threads of the plastic bolt If the nut does not unthread easily. Use your fingers or a screwdriver to pry up the plastic housing to uncover the bolt.

Want to put on a new toilet seat but cant get bolts to loosen 5 answers Edit Comment. Using a small sledge hammer. Yes I was holding it from underneath and they would not turn.

Drill a hole straight up through the inside edge of the nut. How do you fix a discolored toilet seat. Use a putty knife to scrape the plastic off as it melts.

2 Remove the nut from. They all work fine. The plastic bolts are hidden under a small plastic housing at the top of the seat.

Ive never used an OMT but advise caution on any impact lest you break the ceramic. Hold the bolts in place with the screwdriver and start moving the wrench on the bolt to give it enough tight. Heat will also melt the plastic off to where you can peel it off with pliers but again dont heat the ceramic dont drip molten plastic and dont let the pliers slip and hit ceramic.

Then pull the whole thing upwardwith a wiggle and out. Place the plastic nuts in a safe location and pull up on the back of the toilets seat. I replaced the seats on all 3 of them.

If theyre covered with plastic caps pop them off with your fingers or a flat screwdriver. My Phillips head screwdriver is now useless on it and the screwhead itself is pretty. If you cant spot any bolts or screws from on top of the seat check underneath.

Use a screwdriver and a wrench to give enough tight to the bolts. Locate the bolts that attach the toilet seat to the toilet at the back of the seat. Use new bolts to secure the new toilet seat.

You should see the ends of a screw or a mounting nut. Cant remove toilet seat. Back Next.

I bought an impact screwdriver from Amazon and went to work. Remove the seat bolts and lift off the seat. Then press down on the screw.

How Do I Remove Plastic Nut On Toilet Seat Pro Construction Forum Be The Pro